A plain gray broom-finish driveway in Kerman typically runs $6 to $12 per square foot installed. A standard 600 square foot two-car driveway usually lands between $3,600 and $7,200. That is the Fresno County band, not a national average. Color or stamping pushes toward the $10 to $22 range.
A concrete driveway in Kerman typically costs $6 to $12 per square foot installed for a plain gray broom finish, more for color or stamping. We build on compacted Class 2 base with a 4,000 PSI mix, cut control joints on time, and pull the City of Kerman encroachment permit when the approach meets the street.
What a driveway install includes in Kerman
A driveway is more than the slab you see. What decides whether it lasts 10 years or 35 is under the concrete and along the edges.
Our standard Kerman driveway covers tear-out and haul-off of the old slab, grading and excavation to depth, a compacted Class 2 base, set forms, rebar or wire mesh where the load calls for it, a 4,000 PSI mix poured to 4 inches on car driveways, a broom finish for traction, saw-cut control joints, and immediate curing. If the approach ties into a city curb, the encroachment permit and the city driveway detail are part of the job.
We quote the whole thing in writing before we start. No surprise line items once the skid steer arrives.
Driveways for Kerman's housing mix
Kerman is a Fresno County farm town where the median home dates to about 1993. That drives the two kinds of driveway work we do here.
The first is replacement on those 1990s homes. Their original driveways are now around 30 years old, which is old enough that thin slabs and missing joints have started to crack and settle. We tear those out and repour to a proper base, matching the finish and joint lines of the existing walkways so the new slab fits the house.
The second is new work. The Whispering Falls development, 118 single-family homes plus 54 apartments, was approved on August 13, 2025, with groundbreaking expected in early 2026. New homes come with new driveways, and that wave will build over the next few years. For the front-of-house work overall, our concrete work across Kerman covers driveways alongside patios, walkways, and repair.
What a driveway costs in Kerman
Expect to pay in the region of $6 to $12 per square foot installed for a plain gray broom-finish driveway in Kerman. That is the local Fresno County band, not a national average. A standard 600 square foot two-car driveway usually lands between $3,600 and $7,200.
Colored, stamped, or exposed aggregate driveways run higher, typically $10 to $22 per square foot once you add integral color, a pattern, and sealer.
What moves the price up or down:
- Tear-out. Removing and hauling an old 1990s slab adds cost. A fresh pour on open dirt is cheaper.
- Thickness and rebar. A 5 to 6 inch slab with rebar for RV or farm-equipment loads costs more than 4 inch car flatwork.
- Access and length. Longer approaches on the larger lots at the edge of town need more concrete and more base.
- Finish. Broom is the baseline. Color, stamping, and sealer each add per-square-foot cost.
- Site work. Soft subgrade or tree roots found during tear-out change the scope, and we tell you before we proceed.
We give a flat, written number after we see the site. Call 559-254-0253 and we will set up a free on-site estimate.
Driveway finish options
Broom Finish
The standard, and for good reason. A light broom finish gives traction on a sloped approach and hides minor wear. It is the most cost-effective finish and the one most Kerman driveways get.
Colored Concrete
Integral color mixed through the batch, so the tone runs full depth and does not wear off the surface. Earth tones read well against the stucco and tile roofs common on Kerman's 1990s homes.
Exposed Aggregate
The top mortar is washed back to reveal the stone. Durable, slip resistant, and good at hiding the dust that comes with farm-town living.
How we pour a driveway that lasts on the Valley floor
Kerman sits on the San Joaquin Valley floor. That gives every driveway two things to handle: heat and moving soil.
Summers here run 100 degrees and up with very dry air, which causes plastic shrinkage cracking if a slab is placed in the afternoon. So we schedule pours for early morning, dampen the subgrade and forms first, keep the mix water to the design amount, and start curing the moment we finish.
What we do not fight here is freeze-thaw. The ground does not stay frozen on the valley floor, so there is no freeze-thaw cycling of a slab. The durability risks are heat during placement and clay soils that shrink and swell as they wet and dry, so a well-compacted base and correct joint layout are the defense. The same base and joint discipline carry over to our driveway installation in Madera, so the standard does not change from town to town.
Kerman driveway FAQ
How much does a concrete driveway cost in Kerman?
Do I need a permit for a driveway in Kerman?
It depends on where the work stops. A driveway that stays on private property is generally exempt from a building permit. But the moment the approach or apron ties into the public right of way, you need a City of Kerman encroachment permit, because Kerman runs its own counter as a Fresno County city. We pull it.
How thick should a driveway be for a Kerman home?
For a standard car and light truck driveway we pour 4 inches over compacted Class 2 base. For a slab that carries an RV, a dually, or farm equipment out on the larger lots at the edge of town, we go 5 to 6 inches with rebar tied on center under the wheel path.
Can you match a new driveway to my 1990s house?
Yes. Most Kerman homes date to around 1993, so we tie new driveways into the original walkways, aprons, and garage slabs from that era. We match slope, joint lines, and finish so the new work does not read as a patch.
How long before I can drive on a new Kerman driveway?
Walk on it after about 24 hours. Wait 7 days before parking a car, when the slab holds roughly 70 percent of its strength. Hold off on an RV or a heavy truck for the full 28 days. In Valley heat we start curing right after finishing, so cure time is not optional.
Is it worth replacing a cracked Kerman driveway or just patching it?
A settled corner or a couple of isolated cracks can sometimes be patched. But a driveway that is thin or cracked across the whole field has usually reached the end of patching. On 1990s homes that first slab is now old enough that a clean tear-out and repour often beats chasing repairs.
Ready to price your Kerman driveway?
Call or text and you will talk to someone who pours driveways for a living. We give a written number after we see the site, and we pull the Kerman encroachment permit.
We respond the same business day, Monday to Saturday, 9:00 AM to 6:00 PM.
- Locally owned and operated in Madera
- Free on-site estimates
- 4,000 PSI mix on residential flatwork
- We pull the encroachment permit
Get Your Free Estimate